Woodworking Plans

🔥+ Woodworking Plans 05 Jun 2020 There are a lot of aspects in building the best outdoor living spaces. ... Ranging from the classic table and chairs to custom installed bars and BBQ grills that bring the comfort ... Urban Rooftops has the skills to design any planter or roof garden.

Woodworking Plans Learn how to build a single shed door the easy way. There are many types of doors you can put on your shed. However, the basic single shed door is the most ...

Diy Dark Wood Water Bottle Stand To Build
0

Cart

Home / Projects / Sliding Wall-O-Tools
Sliding Wall-O-Tools2009-12-08Woodworking Planshow to Woodworking Plans for 2015-02-12 the 1 last update 2020/06/05 https://www.popularwoodworking.com/wp-content/uploads/popwood_logos-01.pnghttps://www.popularwoodworking.com/wp-content/uploads/popwood_logos-01.pngPopular Woodworking for 1 last update 2020/06/05 MagazinePopular Woodworking Magazinehttps://www.popularwoodworking.com/wp-content/uploads/10752_5F00_sliding-113x113.jpg200px200pxhttps://www.popularwoodworking.com/wp-content/uploads/10752_5F00_sliding-113x113.jpg200px200px

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations.

 

 

 

Woodworking Planshow to Woodworking Plans for  

 

Sliding Wall-O-Tools

 

I built this 8-ft.-long shelf system to take advantage of the narrow space in the corner of my garage. When the unit is “closed,” I’ve got ready access to the tools hanging on both doors. By sliding one or both for 1 last update 2020/06/05 doors, I can get to every inch of shelf space behind them. I got everything I needed to build this unit at the home center for about $175.I built this 8-ft.-long shelf system to take advantage of the narrow space in the corner of my garage. When the unit is “closed,” I’ve got ready access to the tools hanging on both doors. By sliding one or both doors, I can get to every inch of shelf space behind them. I got everything I needed to build this unit at the home center for about $175.

 

Woodworking Planshow to Woodworking Plans for The key was to mount the pegboard doors at least 5 in. apart, so I could load the back door with tools and still have it pass behind the front door. I bought two sliding-door hardware kits so each door could slide on its own track. Each kit contains a single length of track designed to hold both doors, two pairs of door hangers and a tracking guide designed to keep both doors in line at the floor. 

 

 

 

 

Woodworking Planshow to Woodworking Plans for How I Built It

 

I installed the shelves first, leaving enough room underneath to store my lawn mower and other garage essentials (photo at left). All three shelves came from a single sheet of plywood. The upper shelves are 11 in. wide and the bottom one is 20 in. I used 11-in. double-mount brackets for the upper shelves and 14-in. double-mount brackets with support arms for the wide bottom shelf.

Woodworking Planshow to Woodworking Plans for  

I mounted the sliding-door tracks on a 2×10 header that I anchored directly above the wide shelf with lengths of slotted angle extending from both the ceiling and wall (upper right photo). 

 

To make the sliding doors, I cut a single sheet of pegboard in half and framed both pieces with 1×2 stock (each door has four vertical stiles for rigidity). I suspended each door from four hangers (center right photo) and fastened the tracking guides, one per door, on the wide plywood shelf (lower right photo). After installing the doors, I blocked the open end of the tracks with a stop.

 

 

 

The doors hang from widely spaced tracks mounted on a 2×10 header. Lengths of slotted angle hold the header securely in place.

 

Woodworking Planshow to Woodworking Plans for for 1 last update 2020/06/05   

 

 

 

The doors glide smoothly on roller-equipped hangers. Each track has two grooves, so you can easily change the spacing between the doors and shelves, if necessary.

 

 

for 1 last update 2020/06/05   

 

 

Woodworking Planshow to Woodworking Plans for Each door has its own tracking guide. My system uses two sliding-door hardware kits. Each kit contains one guide designed for two doors. I customized them with a hacksaw.

 

 

 

the 1 last update 2020/06/05   

 


Product Recomendations

Woodworking Planshow to Woodworking Plans for Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.

American Woodworker Editors
We are delighted to share some of the best AW content here on the PW website.
Recommended Posts
© 2019 Cruz Bay Publishing, Inc. All rights reserved
0

Start typing and press Enter to search

Woodworking Planshow to Woodworking Plans for
Woodworking Planshow to Woodworking Plans for Inside/Outside Frame ClampingProjects, Questions And Answers, Techniques
Delta Unisaw Rebuild Part IIIFeature Articles