Woodworking Plans

🔥+ Woodworking Plans 05 Jun 2020 New Speakers for 2x15" bass guitar cabinet. Nate Groadie, Multi-Way, 0, 20th May 2003 03:38 AM ...

Woodworking Plans Our garage apartment floor plans range in size and layout, and typically feature a kitchen area, a living space and one or more bedrooms.

How To Build A Garden Arbor
Woodworking Planshow to Woodworking Plans for

Project Guide

  • Time for 1 last update 2020/06/05 Required: Time Required: 2-4 hours

  • Difficulty: Intermediate



Tip: When selecting a place in the room to put your bed, measure the available space between surrounding furniture to ensure that you have enough room for the frame.

Cut Lumber

Woodworking Planshow to Woodworking Plans for Purchase and cut the lumber pieces based on the below cut list: 

  • Get four 2- x 4-inch x 8-foot whitewood: cut four 40 ½-inch frame sides and four 13-inch frame center supports 
  • Get four 2- x 4-inch x 10-foot lumber: cut eight 58-inch frame cross members 
  • Get four 1- x 8-inch x 8-foot whitewood: cut two 81-inch apron (sides) and two 62.5-inch apron (head and foot) 
  • Get one 1- x 3-inch x 8-foot whitewood: cut four 14 ½-inch legs (sides)
  • Get one 1- x 4-inch x 8-foot whitewood: cut four 14 ½-inch legs (front and back)

Collect all of the frame cross members and drill two pocket holes on each end with the lumber pieces standing the 1 last update 2020/06/05 vertically.
Collect all of the frame cross members and drill two pocket holes on each end with the lumber pieces standing vertically.

Tip: The holes are drilled at an angle to hide the screws that connect the pieces together. The depth of your pocket holes are determined by the thickness of your cut lumber pieces.

Create the Frame
  • Layout the frame cross member so that you have one on each end of the frame sides.
  • The middle cross members get placed at 13 ½ and 27 inches on the frame.
  • Once they are in place, screw them together.
  • Repeat these steps to make the other half of the bed frame.
  • Line up the long sides of the two frame assemblies.
  • Clamp them together and make sure they’re square.
  • Mark the center of the conjoined assemblies at 18 inches, then drill 3/8-inch holes to bolt the pieces together.
  • Insert the 5/16- x 4-inch bolt into the conjoined pieces with the accompanying cut washer, lock washer and nut. 
  • Add wood glue between the pieces, then tighten to secure.

Tip: Now is a good time to transition the construction to a larger workspace, or place it on the ground, if the area or surface you’re utilizing isn’t large enough.

  • Prop the frame assembly up 1 ½ inches from the ground. You can use scrap pieces of lumber, or 2- x 4-inch and 1- x 4-inch boards. 
  • Line one of the side apron pieces even with the ends of the frame assembly with a 1 ½-inch over hang on the top edge. 
  • Clamp into place. 
  • Measure and drill the holes for the bolts 3 ¼ inches down from the top edge and 1 ½ inches on the overhang side. 
  • Do this at 8, 29, 52 and 73 inches. The holes should be in the center of the 2- x 4-inch frame assembly. 
  • Repeat this step to attach the other side apron. 
  • Line up the foot apron so that the ends are flush with the outer edge of the side apron pieces. 
  • Clamp into place. 
  • Drill holes for the bolt 3 ¼ inches down from the top edge. Do this at 8, 31 ¼ and 54 ½ inches. 
  • Add wood glue, then insert and tighten the bolts in place. 
  • Repeat this step to attach the head apron.


Attach the Legs
  • Flip over the frame assembly to attach the legs. 
  • Align the legs one at a time with the end of the side apron. 
  • Secure in place with brad nails. 
  • In the same way that you did the side legs, attach the front and back legs. The only difference is that they will be aligned flush with the top of the apron and the face of the side legs.
Attach Supports
  • Place center supports onto the second and fourth cross frame members at 30 ½ inches. 
  • Place center supports onto the middle cross frame member at 24 inches. 
  • Use your speed square to ensure the supports are square with the frame assembly. 
  • Secure in place with wood glue and 2 ½-inch pocket hole screws. 
  • Sand everything smooth and wipe it down to get rid of the sawdust.
  • You can now cover each hole with a pocket hole plug. 
  • Apply a coat of paint or stain to complement your bedroom decor.

Don''t own all of the tools needed to complete this DIY project. Rent tools and trucks for any project at The Home Depot. Then, once you have completed your bed frame, consider adding a DIY wooden headboard to complete the rustic look. 


Explore More on Homedepot.com