DIY Murphy Bed Desig

🔥+ DIY Murphy Bed Desig 10 Jul 2020 It's essential to ensure the right size workbenches so you can work standing up without bending, that will save ... ​Windsor Design 4 Drawer WorkBench; 2.7 7.

DIY Murphy Bed Desig ... Recently Sold Properties. Audubon Naples Florida Homes for Sale $575000 - $3490000. ... A masterpiece of design featuring 14,000 sq. Ft. Under roof ... Second bedroom en-suite and sliding glass doors to courtyard/ pool. Two story guest ...

Wood Bathtub Caddy
STIHL Blog
STIHL Blog DIY Murphy Bed Desighow to DIY Murphy Bed Desig for > Practical the 1 last update 2020/07/10 knowledgePractical knowledge > DIY – Tree trunk lamp
in Practical knowledgeposted by

Why not bring the woods into your own garden, or even your home? This DIY guide shows you how to turn a tree trunk into a decorative light using your STIHL chainsaw. The tree trunk lamp is very practical, and can also be used as a stool or side table.

Not only does this handmade wooden lamp make a great garden or balcony light, it’s also a real eye-catcher in the living room.

Selecting your wood

In principle, you can use any kind of coniferous wood to make this decorative lamp, such as larch, pine, or spruce. But it need not be fresh wood – not at all: even cracked, slightly splintered trunks can be used. These cracks add to the natural appearance of the lamp and help to make it unique. The only constraint is that the wood mustn’t be damp or rotten: the drier the wood the better suited it is.

It’s a one-of-a-kind pattern and slivers of light that give these wooden lamps have their own special charm. These are formed naturally when the wood dries quickly, and only need to be gently expanded using the chainsaw. If you’re working with a piece of wood that doesn’t have any dry cracks you can create some using the chainsaw as you construct the lamp.

Make sure your chosen piece of wood doesn’t have any for 1 last update 2020/07/10 branches or forks, and that it has grown straight. We recommend using wood without bark, or that you remove the bark before starting work.Make sure your chosen piece of wood doesn’t have any branches or forks, and that it has grown straight. We recommend using wood without bark, or that you remove the bark before starting work.

Protective clothing

DIY Murphy Bed Desighow to DIY Murphy Bed Desig for Even amateur artists need to use appropriate protective equipment when using a chainsaw. Protection begins at the head: wear safety glasses or face protection and use some form of noise prevention, such as ear defenders. Hands, legs, and feet can be protected by work gloves, trousers with cut protection, and boots with cut protection inserts.

If you’re using a STIHL cordless chainsaw you won’t need any noise prevention. Find out more about protective equipment when sawing with a chainsaw.

Please note, some countries may have specific requirements for personal protective equipment, and be aware that protective equipment is no substitute for working safely. Therefore, please also always follow the operating instructions for the tool you’re the 1 last update 2020/07/10 using.Please note, some countries may have specific requirements for personal protective equipment, and be aware that protective equipment is no substitute for working safely. Therefore, please also always follow the operating instructions for the tool you’re using.

DIY Murphy Bed Desighow to DIY Murphy Bed Desig for You can find out more about using chainsaws safely on our website.

Step 1: Materials required for the DIY lamp

  • STIHL chainsaw
  • Log, preferably without bark
  • Folding ruler
  • Marking chalk/pencil
  • Angle grinder
  • Heavy sawhorse
  • LED fairy lights for outdoor use

These are the materials you’ll need to make your tree trunk lamp.

Step 2: Mark where to plunge cut

Before you start hollowing out the trunk, you need to draw marks for where your plunge cuts will go. First, fix the log onto a solid sawhorse using a chain or a tensioning belt, then draw a square on the cross-section of the trunk. Be sure not to make the outer rim too narrow, otherwise the lamp may not be sufficiently stable.

Mark where to make plunge cuts.

Step 3: Hollowing out the log

Before hollowing out the log, it’s a good idea to first make a mark on the guide bar of your chainsaw: this will ensure you make each plunge cut to the sane depth (e.g. 25 cm). You could use a pencil to mark the length on the guide bar, or make a mental mark by cutting to a specific letter of the STIHL logo on the bar.

Now you can make your cuts. As you cut all four sides, position the tip of the guide bar on at an angle into the wood on each side of the square, so that the removed part is in the shape of a pyramid. Make sure you don’t damage the outer edges of the wood as you work.

Please pay particular attention to the following points during this step:

  • This method of working means an increased risk of kickback. Make sure you always follow the safety component of the operating instructions, and only use this technique if you’re familiar with it.
  • Use a solid, heavy sawhorse. Plunge cutting can cause powerful horizontal forces, which in some circumstances can make a lighter sawhorse fall over.

We recommend using a new chain with a smaller distance between the depth gauge and saw teeth. This should make the plunge cutting a little easier to manage. Saw chains with a larger distance between the depth gauge and saw teeth are more likely to cause kickback.

Use the chainsaw to make the plunge cuts, going slightly diagonally into the wood, to hollow out the inside of the lamp.

Step 4: Measure the lamp housing

Use a folding ruler to measure the deepest point of the hollow space inside the trunk. Add around 3-5 cm to that measurement, and mark the resulting length on the outside of the trunk.

Make a separating cut at the mark to cut the lamp housing to the appropriate size. Make sure you hold the saw straight.

Use the chainsaw to cut the lamp housing to the right size.

Step 5: Sawing dry cracks to make light slits and adding mitre cuts

Fix the cut piece of wood to a sawhorse. Now you can use the chainsaw to deepen the dry cracks and expand them until they reach the hollow space in the centre of the lamp. Saw the cracks down to the fastening. You can also add new cuts. We recommend having four to six recesses for the light to shine through, though you can have more or fewer, depending on the thickness of the tree trunk and your personal taste.

Tip: STIHL cordless chainsaws, are particularly well suited for this application, because they have very narrow chains and guide blades. Additionally, they mean you can avoid noise and emissions in your own garden, as cordless power tools are particularly quiet and emissions-free.

DIY Murphy Bed Desighow to DIY Murphy Bed Desig for You can also add mitre cuts around the top of the lamp to round the edges. We recommend you use the incoming saw chain – i.e. the lower end of the guide bar – to make the mitre cuts. If you use the outgoing chain, there’s a risk the edges might splinter.

Then turn the lamp over, fix it in position, and repeat the process used on the upper side for working on the dry cracks and making the mitre cuts.

Use the chainsaw to saw recesses or expand natural dry cracks.

Step 6: Fine sanding and treatment

If you like, you can use an angle grinder to smooth the wood’s edges or the light slits.

You can decide whether or not to treat the wood. If you plan to use the lamp in the garden at a later point, the wood doesn’t necessarily need to be treated – it can develop a lovely patina. If you’re going to be using the lamp inside, however, we recommend treating it with hard wax oils.

DIY Murphy Bed Desighow to DIY Murphy Bed Desig for Put the finishing touches to for 1 last update 2020/07/10 the lamp using a grinder.Put the finishing touches to the lamp using a grinder.

Your handmade tree trunk lamp is finished!

Take the string of fairy lights and place these inside the tree trunk. If you want to use the lamp in your garden, you must choose a water-resistant and weatherproof string of LED fairy lights. Make sure the plug socket for the power supply is also protected against the weather – e.g. using a plug safety box.

If necessary, you can use the chainsaw to saw a small recess in the base of the lamp. This only needs to be as high and wide as the lamp’s power supply. When the lamp is in position, the cable can run through the small recess, improving safety and ensuring your lamp stands up straight.

The finished DIY wooden lamp

Read comments and comment:

2 thoughts on “DIY – Tree for 1 last update 2020/07/10 trunk lampDIY – Tree trunk lamp

  1. DIY Murphy Bed Desighow to DIY Murphy Bed Desig for If you enjoy free woodworking plans, you will love woodprix. Get inspired by all the endless possibilities of furniture plans and other wood projects to build, for both indoors and outdoors.

  2. just get a log, and cut it from top to nearly bottom in for 1 last update 2020/07/10 a star shape, so that all cuts meet in the middle. then light it in the middle and let it burn. way better and faster.
    Viva la Grischa!
    #JonseredRocksjust get a log, and cut it from top to nearly bottom in a star shape, so that all cuts meet in the middle. then light it in the middle and let it burn. way better and faster.
    Viva la Grischa!
    #JonseredRocks

DIY Murphy Bed Desighow to DIY Murphy Bed Desig for Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *Your email address will not be published. Required fields are marked *

DIY Murphy Bed Desighow to DIY Murphy Bed Desig for

Cookies on the STIHL website


We use cookies to ensure that we give you the best experience on our website. If you continue without changing your settings, we''http://www.stihl.com/imprint-privacy-policy.aspx''button''0' data-cli_action="" id="" class="" style="">OK

Privacy & Cookies Policy
Necessary Always Enabled